Aftermarket IEC contact that fits Devialet 200 - Printable Version +- Devialet Chat (https://devialetchat.com) +-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat) +--- Forum: Tweaker's Corner (https://devialetchat.com/Forum-Tweaker-s-Corner) +--- Thread: Aftermarket IEC contact that fits Devialet 200 (/Thread-Aftermarket-IEC-contact-that-fits-Devialet-200) Pages:
1
2
|
Aftermarket IEC contact that fits Devialet 200 - octaviars - 16-Jun-2015 I am going to rebuild a couple of powercables so that they fit my Dev 200, I got a Furutech FI-15Plus (G) that some one sugested would fit under the cover but it did not do that. Does anyone know if the Furutech FI-15E fits under the cover? It is a little bit smaller than the Plus model. If the FI-15E does not fit I was looking at the Martin Kaiser 794 model that seems to be a decent contact that fits under the cover. RE: Aftermarket IEC contakt that fits Devialet 200 - thumb5 - 16-Jun-2015 I am using Furutech FI-15E with my 200s; it fits under the rear cover, but only just. RE: Aftermarket IEC contact that fits Devialet 200 - octaviars - 16-Jun-2015 (16-Jun-2015, 17:34)thumb5 Wrote: I am using Furutech FI-15E with my 200s; it fits under the rear cover, but only just. And the cover does not lift up over the chassi in the side were the IEC is? RE: Aftermarket IEC contact that fits Devialet 200 - mauidan - 16-Jun-2015 Cardas - 3455R Female Power Connector RE: Aftermarket IEC contact that fits Devialet 200 - Rufus McDufus - 16-Jun-2015 I've made a few cables in the past with the Martin Kaiser connector. It's good - very tight. The cables all sounded good which is a plus! RE: Aftermarket IEC contact that fits Devialet 200 - thumb5 - 16-Jun-2015 (16-Jun-2015, 17:57)octaviars Wrote:(16-Jun-2015, 17:34)thumb5 Wrote: I am using Furutech FI-15E with my 200s; it fits under the rear cover, but only just. No, it fits flush. I am fussy too RE: Aftermarket IEC contact that fits Devialet 200 - Ron D - 16-Jun-2015 Otto Heil makes at least one model that works, wish I knew which model to tell you but mine is wrapped in shrink-wrap from the cable manufacturer. I much preferred to use the cable manufacturer's initial IEC (much better build quality) but it's size (height) negated the attaching of the rear panel. RE: Aftermarket IEC contact that fits Devialet 200 - octaviars - 17-Jun-2015 (16-Jun-2015, 22:23)thumb5 Wrote:(16-Jun-2015, 17:57)octaviars Wrote:(16-Jun-2015, 17:34)thumb5 Wrote: I am using Furutech FI-15E with my 200s; it fits under the rear cover, but only just. Sounds good. RE: Aftermarket IEC contact that fits Devialet 200 - Supra - 21-Jun-2015 heard AET is also good. RE: Aftermarket IEC contact that fits Devialet 200 - rwjr44 - 21-Jun-2015 Shunyata sells a short PC made for this purpose it is called the Shunyata Universal Power Adapter. I thought about it but decided that wasn't the solution for me. Since my D200 is in a rack, I don't install the rear cover plate and enjoy the sound of the Synergistic Hologram A. |