Can i connect phantom reactor to a behringer umc202 audio interface? - Printable Version +- Devialet Chat (https://devialetchat.com) +-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat) +--- Forum: Phantom II (95 DB, 98 DB, Reactor 600 & 900) (https://devialetchat.com/Forum-Phantom-II-95-DB-98-DB-Reactor-600-900) +--- Thread: Can i connect phantom reactor to a behringer umc202 audio interface? (/Thread-Can-i-connect-phantom-reactor-to-a-behringer-umc202-audio-interface) |
Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 10-Feb-2019 Hello, I am about to pull the trigger on 2 reactors for a pc setup. Until the stereo update is available, could I plug these into my Behringer Uphoria UMC HD 202 audio interface for stereo? Should I install the spark app on my Windows pc? I plan to buy them next week. Many thanks! RE: Can i connect phantom reactor to a behringer umc202 audio interface? - ralphy - 11-Feb-2019 I wonder how these beauties perform in a near-field environment. Keep in mind that the analog input is limited to 48 kHz and up to 96 kHz for optical. Ideally you'd want to use optical but I am not sure how you'd connect the cables to make the 2 phantoms play in stereo. RE: Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 11-Feb-2019 Thank you for the reply. I think I need a toslink splitter. Apparently my computer can output stereo toslink so if I get a junction I should be able to feed 2 optical signals to the reactors. I think.... RE: Can i connect phantom reactor to a behringer umc202 audio interface? - ralphy - 11-Feb-2019 (11-Feb-2019, 19:53)RMK Wrote: Thank you for the reply. Wouldn't a toslink splitter simply split the signal into 2 identical outputs? That won't get you stereo playback. I believe you would first need to convert the digital signal from your computer to analog so you can split the signal into L and R (stereo). Too bad Phantom Reactors are limited to 48 kHz when connected to analog. RE: Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 12-Feb-2019 I've bought two 6.35mm to 3.5mm cables so I can temporarily connect to my pc in stereo. The phantoms arrive tomorrow so I'll update how I get on RE: Can i connect phantom reactor to a behringer umc202 audio interface? - ralphy - 15-Feb-2019 (12-Feb-2019, 06:45)RMK Wrote: I've bought two 6.35mm to 3.5mm cables so I can temporarily connect to my pc in stereo. So... how did it go? Did you manage to make your 2 phantoms play in stereo? RE: Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 15-Feb-2019 Sure did. Just need to sort out my cable spaghetti now. https://youtu.be/DiH1AAcXUk0 RE: Can i connect phantom reactor to a behringer umc202 audio interface? - ralphy - 15-Feb-2019 Nice! Would you say the phantom reactors are good speakers for near-field use? How do they sound at low volumes? RE: Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 15-Feb-2019 So far so good but I would imagine they need a bit of space to breathe. I had to go to work so haven't really listened that much yet. Just wanted a test run. So far so good. RE: Can i connect phantom reactor to a behringer umc202 audio interface? - RMK - 17-Feb-2019 Do you guys leave the phantoms on all the time or turn off at the back when you are finished using? |