Devialet Chat

(12-Jun-2018, 15:55)tategoi Wrote: [ -> ]What iOS app?

Apple App „Expert Remote“!

(12-Jun-2018, 11:56)K4680 Wrote: [ -> ]Hello, after 3 days test with upnp streaming or usb no problems. SQ with upnp from melco and TIDAL very good, without any interruptions or disturbances. Oh, see there the ios app works again!
The guys from Devialet do a good job!

So what has changed with the iOS app exactly?  The iOS app has worked for me through all the previous beta firmware versions.  To be clear, the iOS app has been working, but it has been unstable, dropping out and reconnecting periodically.  So is it a case of it being stable now, or did it not work at all for you at all when running the beta firmware?

(12-Jun-2018, 17:32)Confused Wrote: [ -> ]

(12-Jun-2018, 11:56)K4680 Wrote: [ -> ]Hello, after 3 days test with upnp streaming or usb no problems. SQ with upnp from melco and TIDAL very good, without any interruptions or disturbances. Oh, see there the ios app works again!
The guys from Devialet do a good job!

So what has changed with the iOS app exactly?  The iOS app has worked for me through all the previous beta firmware versions.  To be clear, the iOS app has been working, but it has been unstable, dropping out and reconnecting periodically.  So is it a case of it being stable now, or did it not work at all for you at all when running the beta firmware?

Hi, stable until now (without interruption)!

Hello, I have upgraded my D250 Core to the new firmware - when I turn on the D250 the display shows -35 db (my default) - but the remote app shows -97,5 db - When I change the input from USB to Air the remote app shows -35 db but when I change it back to USB the remote app now show -42 db

What to do ?

Nothing as the remote app is not supported anymore. I do occansionally have the same issue as you describe.

installed update tonight, all working fine ios app working but was spasmodic on beta.

I updated from beta yesterday without any hitches. Actually even with betas I haven't had much trouble. However, my setup is relatively simple with no WiFi and no UPnP. Just checked the iPad remote (I usually use Roon) and all the settings are correct there too. This B.B. has been relatively quiet of late, is that good news for Devialet or not?

(10-Jun-2018, 15:46)K4680 Wrote: [ -> ]FW 12.3.0 installed. Without problems, according to txt some errors are eliminated. Well, it works!
Config, now possible via browser!

Are you saying that I can now change configuration remotely via ethernet without pulling out that SD card?

That is what I have been wishing for.  

I cannot seem to find it via the online configurator, could you tell us where you found that option?

(14-Jun-2018, 03:42)agentsmith Wrote: [ -> ]

(10-Jun-2018, 15:46)K4680 Wrote: [ -> ]FW 12.3.0 installed. Without problems, according to txt some errors are eliminated. Well, it works!
Config, now possible via browser!

Are you saying that I can now change configuration remotely via ethernet without pulling out that SD card?

That is what I have been wishing for.  

I cannot seem to find it via the online configurator, could you tell us where you found that option?

Find out the IP address of your Dev on your local network, then type this IP into your browser window

(14-Jun-2018, 03:42)agentsmith Wrote: [ -> ]

(10-Jun-2018, 15:46)K4680 Wrote: [ -> ]FW 12.3.0 installed. Without problems, according to txt some errors are eliminated. Well, it works!
Config, now possible via browser!

Are you saying that I can now change configuration remotely via ethernet without pulling out that SD card?

That is what I have been wishing for.  

I cannot seem to find it via the online configurator, could you tell us where you found that option?

With the free app Fing (iPhone / iPad) you can find the IP address. Enter in the browser.