+- Devialet Chat (https://devialetchat.com)
+-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat)
+--- Forum: Support Desk (https://devialetchat.com/Forum-Support-Desk)
+--- Thread: Companion Info Display not synching with Master (/Thread-Companion-Info-Display-not-synching-with-Master)
Companion Info Display not synching with Master - Foggy916 - 23-Apr-2015
When holding down Tone on the remote and pulling up the info display (temperatures, configs, SW version, levels, etc.), the companion and master display are no longer in synch (off by one page). It was in synch earlier but I updated my firmware on the master today....even with my SW version already being at 7.1.1 (reason being I couldn't get SAM level % to display). Good news is that the firmware update worked and it did resolve the SAM level % showing up but now the problem is that the master and companion are no longer in synch when displaying info. I've tried rebooting by holding power button down and also unplugging power on both units but still no resolution. Tried reloading both SD cards with the same config and still nothing. Makes no sense since the only difference from when it synched properly was the firmware update and there was no changes to my config.
Any suggestions?
Companion Info Display not synching with Master - amabrok - 23-Apr-2015
(23-Apr-2015, 18:52)Foggy916 Wrote: When holding down Tone on the remote and pulling up the info display (temperatures, configs, SW version, levels, etc.), the companion and master display are no longer in synch (off by one page). It was in synch earlier but I updated my firmware on the master today....even with my SW version already being at 7.1.1 (reason being I couldn't get SAM level % to display). Good news is that the firmware update worked and it did resolve the SAM level % showing up but now the problem is that the master and companion are no longer in synch when displaying info. I've tried rebooting by holding power button down and also unplugging power on both units but still no resolution. Tried reloading both SD cards with the same config and still nothing. Makes no sense since the only difference from when it synched properly was the firmware update and there was no changes to my config.
Any suggestions?
I have the same. This is one of the of the reported bugs of dual mono configuration
Sent from my iPhone using Tapatalk
RE: Companion Info Display not synching with Master - Confused - 23-Apr-2015
I had similar issues when trying to configure an input on the companion. A bit of experimenting, reconfiguring, and indeed luck, resulted in getting everything back in sync.
RE: Companion Info Display not synching with Master - dylanttt - 27-Apr-2015
i had the same thing ,and finally worked it out by clicking on chaining settings and put a tick beside chaining input and not for shared sources from slave, hope that helps
RE: Companion Info Display not synching with Master - dylanttt - 27-Apr-2015
i can not use input 1 on my slave unit,i have tried several ways and can not work it out,i have linked the 2 units with a 3.5 cable
RE: Companion Info Display not synching with Master - completeluxury - 27-Apr-2015
(27-Apr-2015, 11:04)dylanttt Wrote: i can not use input 1 on my slave unit,i have tried several ways and can not work it out,i have linked the 2 units with a 3.5 cable
in the post above this one you said that you unticked the box "share sources from slave"
this is why your input on the slave does nothing.
RE: Companion Info Display not synching with Master - Foggy916 - 27-Apr-2015
(27-Apr-2015, 10:47)dylanttt Wrote: i had the same thing ,and finally worked it out by clicking on chaining settings and put a tick beside chaining input and not for shared sources from slave, hope that helps
Tried it. Nope. Still no luck.
RE: Companion Info Display not synching with Master - Foggy916 - 17-May-2015
Upgraded firmware solved my problem! All set.