Trinnov Amethyst and Altitude32 - Roon Ready - Printable Version +- Devialet Chat (https://devialetchat.com) +-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat) +--- Forum: Streaming (https://devialetchat.com/Forum-Streaming) +--- Thread: Trinnov Amethyst and Altitude32 - Roon Ready (/Thread-Trinnov-Amethyst-and-Altitude32-Roon-Ready) |
Trinnov Amethyst and Altitude32 - Roon Ready - baconbrain - 23-Sep-2017 Once again not Dev specific, but for Trinnov owners certainly interesting... At the rate Roon is rolling this functionality out, I am beginning to wonder when my refrigerator will be Roon Ready? Trinnov Amethyst and Altitude32 - Roon Ready - Bob58 - 24-Sep-2017 Thank's for information. RE: Trinnov Amethyst and Altitude32 - Roon Ready - baconbrain - 11-Nov-2017 Update: Prompted by Trinnov’s decision to enable RAAT for the Amethyst and the Altitude32, I decided to take the plunge and upgrade from my ST-2 HiFi to an Amethyst. This resulted in following modifcation of my signal chain: 1) Removal and sale of my SoTM 200 Ultra 2) Removal and sale of my Mutec MC-3+ USB 3) Complete removal of the USB connectivity 4) Establishment of a direct bridged ethernet connection between the Amethyst and my Roon Server The obvious result of this was a signifcant reduction of components in the chain while maintaining a similiar level of SQ. So for those Trinnov owners who may be considering something similiar, it IMO was worth the investment. RE: Trinnov Amethyst and Altitude32 - Roon Ready - john_h - 13-Jul-2018 (11-Nov-2017, 13:51)baconbrain Wrote: Update: Prompted by Trinnov’s decision to enable RAAT for the Amethyst and the Altitude32, I decided to take the plunge and upgrade from my ST-2 HiFi to an Amethyst. Curious how you are using your Amethyst with the D250. Are you using an AES/EBU connection from the Amethyst and using the D250 DAC or using the Amethyst DAC and running analog into the D250? I have read in other posts that there is a preference to use the analog connection and the Amethyst DAC which seems counter intuitive to me given the extra D-A-D-A conversion. I have just taken the plunge on a Trinnov Altitude 32 and thinking through how to set it up with a D440, 4 subwoofers, Raidho C1.2's, and integrate into an ATMOS multichannel system. I am debating if I should repurpose or sell the D440 if only used for its amplification and simplify the setup with Bel Canto Ref600M's for the Raidho's. Any thoughts from Trinnov users? RE: Trinnov Amethyst and Altitude32 - Roon Ready - baconbrain - 19-Jul-2018 (13-Jul-2018, 15:19)john_h Wrote: Curious how you are using your Amethyst with the D250. Are you using an AES/EBU connection from the Amethyst and using the D250 DAC or using the Amethyst DAC and running analog into the D250? I have read in other posts that there is a preference to use the analog connection and the Amethyst DAC which seems counter intuitive to me given the extra D-A-D-A conversion. Hi John_h, Well my precious Dev is history, I replaced it, and my passive speakers, with the Kii Three‘s. Given your plans, it sounds like the 440 might be a bit surplus. Have fun with the Altitude, it‘s a fantastic piece of kit! |