Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Cartridges and phono settings
Hello Jens yes it is Wery good the transformer. But you still say that i must connect wia MM settings ,or Regards Finn
Devialet 220pro ,dynaudio C1 signature ,speaker cable ,and other cable audio note , turntable Audio note tt2,caridge ortofon cadenza Black, MC trafo ortofon verto , blueray player primare BD 32 mrk 2, use altso as a cd player With very good Sound.
Reply
I just placed a new Dynavector 10x5 on my Pro-Ject RPM 5.1 turn table. Using the default settings from RAM this sounds ok, but i am not thrilled yet. I am not sure if and how long such a cartridge has to break in and if there are better settings for it then just the default...

Is there someone else with experience with this cartridge?
Sonus Faber Olympica II -> Chord Signature -> Devialet 200 / Anthem MRX 710 / HD-Plex H1.S based silent HiFi PC -> Roon -> HD-Plex Linear Power Supply / Pro-Ject RPM 5.1 -> Dynavector 10X5 / B&W MT-60D
Reply
(13-Oct-2016, 22:17)Bartype Wrote: I just placed a new Dynavector 10x5 on my Pro-Ject RPM 5.1 turn table. Using the default settings from RAM this sounds ok, but i am not thrilled yet. I am not sure if and how long such a cartridge has to break in and if there are better settings for it then just the default...

Is there someone else with experience with this cartridge?

All MC cartridges that I have owned needed a break in of 50 to 100 hours. 
Manufacturers usually recommend a load higher than something or somewhere between two numbers.  If you increase the load the sound becomes brighter, more detailed and thinner. There is no one setting that is correct. If a recommended load for a cartridge is between 50 and 500 ohms the automatic RAM setting would be 200 - 300 ohms. That does not necessarly mean it is the best setting for your system. In my system I have found that a load 20 times the internal resistance of the cartridge provides the best balance for me.
Devialet 200 - Kuzma Stabi S - Kuzma Stogi Ref - Lyra Delos - REL B2 - Epos 12.2 - Creek Evolution CD - DIY silver cables
Reply
Thank you for your tips! Considering your answer i think it's best to break the cartridge in first before changing something from the RAM settings.

So, i am going to listen all my LP's from A to Z and see/hear what happens Smile




(19-Oct-2016, 19:02)lookslikerain Wrote:
(13-Oct-2016, 22:17)Bartype Wrote: I just placed a new Dynavector 10x5 on my Pro-Ject RPM 5.1 turn table. Using the default settings from RAM this sounds ok, but i am not thrilled yet. I am not sure if and how long such a cartridge has to break in and if there are better settings for it then just the default...

Is there someone else with experience with this cartridge?

All MC cartridges that I have owned needed a break in of 50 to 100 hours. 
Manufacturers usually recommend a load higher than something or somewhere between two numbers.  If you increase the load the sound becomes brighter, more detailed and thinner. There is no one setting that is correct. If a recommended load for a cartridge is between 50 and 500 ohms the automatic RAM setting would be 200 - 300 ohms. That does not necessarly mean it is the best setting for your system. In my system I have found that a load 20 times the internal resistance of the cartridge provides the best balance for me.
Sonus Faber Olympica II -> Chord Signature -> Devialet 200 / Anthem MRX 710 / HD-Plex H1.S based silent HiFi PC -> Roon -> HD-Plex Linear Power Supply / Pro-Ject RPM 5.1 -> Dynavector 10X5 / B&W MT-60D
Reply
I update to 10.0.5 software use the settings AS recommende bye Jens and no no Hiss i play -20 i shall put my Ear Wery close too my speaker and there is a little too hear , it is the bedst settings i have too my dev 200 . I am very glad
Devialet 220pro ,dynaudio C1 signature ,speaker cable ,and other cable audio note , turntable Audio note tt2,caridge ortofon cadenza Black, MC trafo ortofon verto , blueray player primare BD 32 mrk 2, use altso as a cd player With very good Sound.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)