Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
440 master standby and companion off ??
#1
Recently received my 440 Pro from the dealer. Noticed yesterday, that the master had 10.0.2 software (400 w) and the companion had 10.0.4 software (430 w) - upgraded both to software 10.0.5.
Before the upgrade when both set in standby mode (short pres on the on/off button on the remote), both dimmed the display - after the upgrade, the master dim the display, but the companion turn the display completely off.
I use the daisy chain (trigger cable) between the units, and has one input active on the companion.

Any solutions to get the dimmed display back on both when in standby mode?

Best wishes; Jens
Devialet Expert 440 Pro, AudioQuest Wild Digital RCA-RCA / SimAudio MOON NEO 260D CD Transport, AudioQuest Wild Digital AES/EBU / Dali Epicon 2, Transparent Audio Super BiWire / B&W DB1, 2 x AudioQuest Husky Analog RCA-RCA / BlueSound Vault 2, AudioQuest Diamond Digital RCA-RCA + AudioQuest Diamond Toslink / Supra Ethernet 8 cables / Various AudioQuest power cables
Reply
#2
Mine both have the display dimmed, I use the trigger cable to, must be something in the config.
Air 3, Rega P9 with Dynavector XX2Mk2 > 440 Pro > Sonus Faber Guarneri Evolution
Reply
#3
On my 1000 Pro with 10.0.5 the companion display goes off in standby mode so I think that is what is supposed to happen
UK kit - Technics SP10 - Technics EPA-501  - AT33SA - NUC5i3 - Rock - Roonserver - Roon AIR - Devialet 1000Pro - Blue Jeans Speaker Cable (1 metre each side) - Magico S5

Spain kit - NUC5i3 - Linux  - Roonserver - microRendu - LPS1 PSU - Devialet D120 - Ergo IX speakers
Reply
#4
On my dealers 1000 Pro with 10.0.5 the companion display also goes off in standby mode, so it can happen it is normal with the dual Pro range.

If any with dual Pro models with SW 10.0.5 has dimmed displays in both units when they are set in stand-by, please let me know.

Best wishes; Jens
Devialet Expert 440 Pro, AudioQuest Wild Digital RCA-RCA / SimAudio MOON NEO 260D CD Transport, AudioQuest Wild Digital AES/EBU / Dali Epicon 2, Transparent Audio Super BiWire / B&W DB1, 2 x AudioQuest Husky Analog RCA-RCA / BlueSound Vault 2, AudioQuest Diamond Digital RCA-RCA + AudioQuest Diamond Toslink / Supra Ethernet 8 cables / Various AudioQuest power cables
Reply
#5
Strange. My Pro 1000 (10.0.7) leaves the Master dimmed and the Comp display off. As always the companion is not in true standby and is a good few degrees hotter than the Master. Are you saying that your Comp amp actually goes into proper standby? As ever a long press on the Master D-button will switch the display off.
Devialet 1000 Pro; Magico S5 loudspeakers; Metronome T3a Signature CD Transport; Krell Connect Streamer; SME 30/2; Graham Phantom Elite; Koetsu Sky Blue; MacMini/QNAP/Air3/ROON; Audioquest Vodka and Carbon Ethernet; Transparent Reference Digital RCA-RCA; Transparent Reference XL MM2 speaker cable; Transparent Reference mains cable; PS Audio P5 PowerPlant; Artesania and Finite Elemente equipment racks 
North Somerset, UK     
Reply
#6
Hi, are you sure the tripper cable plug into correct socket? as the master tripper cable should plug into lower socket and the slave should plug into upper socket. i did it wrong before as well! Big Grin
Reply
#7
I have 2 configurations for my O d'A, depending whether I am using my horns or conventional speakers.
I have no idea how it happened but with one config both displays are dimmed, with the other only the master is dimmed and the slave is off.
I found it odd but haven't let it bother me!
Devialet Original d'Atelier 44, Goldmund Reference/T3f /Ortofon A90, Goldmund Mimesis 36+ & Chord Blu, iMac/Air, Meridian Control 15, Lynx Theta, Tune Audio Anima, Goldmund Epilog 1&2, REL Studio. Dialog, Silver Phantoms, Branch stands, copper cables (mainly).

Reply
#8
I make only a quick press on the on/off button on the remote, and master get dimmed and the companion switch completely off its display. A long press on the remote turn both displays off.
The link cable is connected right (lower to upper).
I have the units mounted on the wall with the wallmounts and 25 cm apart. It looks a bit stange with only one dimmed display, and would certenly preferencer both with a dimmed display ... it would look nicier Wink
Devialet Expert 440 Pro, AudioQuest Wild Digital RCA-RCA / SimAudio MOON NEO 260D CD Transport, AudioQuest Wild Digital AES/EBU / Dali Epicon 2, Transparent Audio Super BiWire / B&W DB1, 2 x AudioQuest Husky Analog RCA-RCA / BlueSound Vault 2, AudioQuest Diamond Digital RCA-RCA + AudioQuest Diamond Toslink / Supra Ethernet 8 cables / Various AudioQuest power cables
Reply
#9
(10-Dec-2016, 22:32)JensRoland Wrote: I make only a quick press on the on/off button on the remote, and master get dimmed and the companion switch completely off its display. A long press on the remote turn both displays off.
The link cable is connected right (lower to upper).
I have the units mounted on the wall with the wallmounts and 25 cm apart. It looks a bit stange with only one dimmed display, and would certenly preferencer both with a dimmed display ... it would look nicier Wink

OT, but could we have some pictures please, Jens? It would be nice to see what two on the wall look like.  Smile
Project Eperience X Pack with Ortofon Rondo Red MC, Oppo BDP 105D, Sonos Connect, QNAP HS251+ NAS, Mutec MC-3+USB, Mac 5K running Roon, iPad Pro 12.9" for remote control. Devialet 440 Pro, Sonus faber Olympica ll, Rupert Neve Designs headphone amp.Denon AH-D5000, Sennheiser HD600 and HD800 with Cardas cable,  Van Den Hul The First Ultimate interconnects, GSP Audio Spatia speaker cable.
South Coast England
Reply
#10
I recall that this issue came up a long time ago, unfortunately we never resolved it then either!

http://devialetchat.com/showthread.php?t...audioprana
1000 Pro - KEF Blade - microRendu - Mutec MC3+USB - Pro-Ject Signature 12
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)