No sound from slave inputs with 440 - Printable Version +- Devialet Chat (https://devialetchat.com) +-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat) +--- Forum: Support Desk (https://devialetchat.com/Forum-Support-Desk) +--- Thread: No sound from slave inputs with 440 (/Thread-No-sound-from-slave-inputs-with-440) |
RE: No sound from slave inputs with 440 - Freddie77 - 18-Dec-2018 (17-Dec-2018, 20:16)Elztalbiker Wrote: Identical firmware both units? Yes, both the same. RE: No sound from slave inputs with 440 - Freddie77 - 18-Dec-2018 (17-Dec-2018, 20:28)thumb5 Wrote: Thinking out loud... Are you using a long link cable (more than a couple of metres) and/or high sample rates (more than say 48 kHz)? If so, maybe the cable is working marginally and is OK when data flows one way but not the other. Using a brand new Audioquest 0.75m. I changed an older Chord cable with the same length just in case. RE: No sound from slave inputs with 440 - Pim - 18-Dec-2018 Hi Freddy, Try starting all over again with the configs. A small bug can make life hell because it just doesn't go away. Try the below method. It's worked for me 100% https://devialetchat.com/Thread-How-to-configure-your-Expert-Pim-and-Axel-s-method Good luck! Pim RE: No sound from slave inputs with 440 - Freddie77 - 18-Dec-2018 Thanks Pim, I will try that again. Yesterday I did the anonymous method with Chrome and no cookies and the configuration ended up worse, with no link active between both amps. I will give it a try again using Firefox. One thing I noticed from other people's configurations images is that theirs show the word Chaining in the link input and mine shows Digital 1, no matter what I do it keeps showing as digital 1. I can post a pic later. No sound from slave inputs with 440 - Elztalbiker - 18-Dec-2018 This configs are different. First is for using inputs from slave, second without. Gesendet von iPad mit Tapatalk RE: No sound from slave inputs with 440 - Freddie77 - 18-Dec-2018 (18-Dec-2018, 02:00)Pim Wrote: Hi Freddy, (18-Dec-2018, 15:12)Elztalbiker Wrote: This configs are different. First is for using inputs from slave, second without Mine is like the first one. It looks ok when I create that configuration, but the slave inputs don't work when installed. I was also referring earlier that in some pics the link says Chaining instead of Digital as in these pics. RE: No sound from slave inputs with 440 - Damon - 18-Dec-2018 A possible simple issue with the formatting. Are you certain that the SD cards are fully cleared/ erased when you load a new configuration onto them? Not to ask an insulting question, only thinking / remembering that the Devialet is very sensitive to having a perfect config file. Sometimes after loading a config, some files are left on the card. RE: No sound from slave inputs with 440 - Freddie77 - 18-Dec-2018 (18-Dec-2018, 17:30)Damon Wrote: A possible simple issue with the formatting. Are you certain that the SD cards are fully cleared/ erased when you load a new configuration onto them? Not to ask an insulting question, only thinking / remembering that the Devialet is very sensitive to having a perfect config file. Sometimes after loading a config, some files are left on the card. Yes, I have done it all the time, even reformatting once. RE: No sound from slave inputs with 440 - Pim - 18-Dec-2018 To me it looks like the configurator is buggered. That digital input on the slave HAS to change to Chaning , otherwise I can't see it work. I just went to the configurator and had a go. When you add a slave, that input automatically changes to Chaning. I then changed it to input and after that couldn't change it back to Chaining. So it looks like you need to start again, just add a slave and don't touch it afterwards. Hope that helps. RE: No sound from slave inputs with 440 - Pim - 18-Dec-2018 If you still can't get it to work, send me a PM with your input wishes and I'll make up a config for you and will email it to you. |