+- Devialet Chat (https://devialetchat.com)
+-- Forum: Devialet Chat (https://devialetchat.com/Forum-Devialet-Chat)
+--- Forum: Support Desk (https://devialetchat.com/Forum-Support-Desk)
+--- Thread: No sound from slave inputs with 440 (/Thread-No-sound-from-slave-inputs-with-440)
No sound from slave inputs with 440 - Freddie77 - 17-Dec-2018
Hello,
This weekend I upgraded my system from 220 pro to 440 pro and set it up with the configurator; the main inputs on the master work ok, but the inputs on the slave amp don't get any sound or seem to be active, even though they were properly configured on the configurator and also had the chain link active to share slave inputs. What could be happening? I tried several times the configuration and still was the same.
Thanks.
No sound from slave inputs with 440 - paul.oorbeek - 17-Dec-2018
Did you use 2 connections for this configuration (to enable the inputs on second unit) . When only use second unit for second speaker only 1 connection is used.
Sent from my COL-L29 using Tapatalk
RE: No sound from slave inputs with 440 - Freddie77 - 17-Dec-2018
(17-Dec-2018, 11:03)paul.oorbeek Wrote: Did you use 2 connections for this configuration (to enable the inputs on second unit) . When only use second unit for second speaker only 1 connection is used.Sorry, I didn't understand quite well what you mean. I used a coaxial and a 3.5 as well from the trigger out as per the configurator. The sharing option is ticked as enabled on the coaxial connection.
Sent from my COL-L29 using Tapatalk
RE: No sound from slave inputs with 440 - paul.oorbeek - 17-Dec-2018
(17-Dec-2018, 14:19)Freddie77 Wrote:Ok then i do not know what the issue is unfortunately(17-Dec-2018, 11:03)paul.oorbeek Wrote: Did you use 2 connections for this configuration (to enable the inputs on second unit) . When only use second unit for second speaker only 1 connection is used.Sorry, I didn't understand quite well what you mean. I used a coaxial and a 3.5 as well from the triger out as per the configurator. The sharing option is ticked as enabled on the coaxial connection.
Sent from my COL-L29 using Tapatalk
Sent from my COL-L29 using Tapatalk
No sound from slave inputs with 440 - ghosttipper - 17-Dec-2018
Die you connect the link cable between the units in the right out/inputs?
RE: No sound from slave inputs with 440 - Freddie77 - 17-Dec-2018
(17-Dec-2018, 17:09)ghosttipper Wrote: Die you connect the link cable between the units in the right out/inputs?
Yes, both unit connected through coaxial for link and 3.5 cable from trigger out.
I tried another configuration and didn't work either. After that I went back to the configuration I was using (with not working inputs on the slave) and now I lost the ethernet and wifi connections too.
No sound from slave inputs with 440 - Elztalbiker - 17-Dec-2018
Please delete old configs on both sd cards and load f4om the Website for every unit the config again. That could help.
Good luck
Gesendet von iPad mit Tapatalk
RE: No sound from slave inputs with 440 - Freddie77 - 17-Dec-2018
(17-Dec-2018, 18:19)Elztalbiker Wrote: Please delete old configs on both sd cards and load f4om the Website for every unit the config again. That could help.
Good luck
Gesendet von iPad mit Tapatalk
Thanks, I have tried that a few times, even downloading files with different browsers; and formatting and still the same. Only thing back is ethernet and wifi after unplugging from the switch. I also submitted support ticket through Devialet.
No sound from slave inputs with 440 - Elztalbiker - 17-Dec-2018
Identical firmware both units?
Gesendet von iPad mit Tapatalk
RE: No sound from slave inputs with 440 - thumb5 - 17-Dec-2018
Thinking out loud... Are you using a long link cable (more than a couple of metres) and/or high sample rates (more than say 48 kHz)? If so, maybe the cable is working marginally and is OK when data flows one way but not the other.